4 printer. Es treten direkt mehrere Probleme auf, einmal wie im Titel schon geschrieben "endstop x still triggered after retract" kommt direkt nachdem ich homen will. same Hi everyone, I'm trying to set up Klipper on my CoreXY Printer with TMC2130 on X, Y and Z. Was meint ihr ist es ein Softwareproblem, da ich kurz zuvor ein A user reports a problem with endstop x still triggered after retract when using Klipper firmware for a BTT skr 1. 2 toolboard) for x endstop. The solution is to set homing_retract_dist to 0 in the A user reports a problem with the y-axis endstop triggering after retraction on a Voron 2. Er blinkt nur noch rot. 2. Ich würde einfach zuerst mal einen Factory Reset machen. 2 w/CR Touch and Microswiss DD -- "Endstop x still triggered after retract" I found another post with a configuration file for my same set up (Ender 5 w/CR Touch and . I used the Sensorless Homing feature for X and Y before with Marlin and it worked Normalerweise macht der cr touch direkt beim einschalten Geräusche nun nicht mehr. Klipper's endstop phase system combines the hi, getting error " endstop X still triggered after retract " i have replaced the top switch unit ( see pic ) i couldnt find a replacement switch Ender 5 Pro, 4. My SV08 printer been running well for a while now. But when it tries to home z it crashes into the And give me trouble as shown in title "Endstop z still triggered after retract". cfg stimmt nicht. I have checked the cable wiring guide 17 times and swapped Endstop x still triggered after retract. The QUERY_ENDSTOPS command should report the endstop as "TRIGGERED". If the endstop appears inverted (it reports "open" when triggered and vice-versa) then add a "!" Thus, when a carriage triggers the endstop switch the stepper controlling that carriage should always be at the same stepper motor phase. Endstop on T1 swithed with T0, x triggers properly but dual_carriage The QUERY_ENDSTOPS command should report the endstop as "TRIGGERED". hi, getting error " endstop X still triggered after retract " i have replaced the top switch unit ( see pic ) i couldnt find a replacement switch setup for the bottom one, so i I've noticed that having a non-zero homing_retract_dist setting on an axis (such as the default 5mm) makes homing susceptible to still triggered errors like: "Endstop x still Also entweder ist der X-Endstop defekt oder die printer. When I turn the potentiometer of sensor and I get "Endstop x still triggered after retract" everytime I try it, or even trying to just Home. Endstop checked for continuity, pass 2. X fährt ein stück nach rechts und spuckt den Fehler aus dann dachte ich mir Manuell mal mit den Finger drücken und noch mal homen. Another user suggests adjusting the Hi All. 我用的是 TMC2209 的 无限位回零。 [tmc2209 stepper_x]的配置里面有1个 driver_SGTHRS: 0 参 Gently pushed the bed from underneath with my finger during retract: still no retraction Checked everything is running smoothly by deactivating the motor and winding it by Endstop z still triggered after reset", if i try to run a print the machine tries to home in the z but cannot and has been crashing! I cannot level the machine either as it's alarming that the z is That probe connector (I think) only works for BL touch, I got this exact same behaviour (endstop triggering) and took me all night to debug. After the pin get damaged and replaced with microprobe Hi everyone, this morning I installed the new firmware but as soon as I tried to print I get this error: gcode error:!! Endstop z still Trouble shooting steps taken: 1. When I tried to home the printer a day ago, it homed fine on X and Y, but when it came to the Z axis, the head Nachdem ich den ender6 erfolgrich mit dem pad verbinden konnte wollte ich die "configure" machen will heißen, die ersteinrichtung mit dem "Home"-ing hängt schon bei mir Hello, I updated yesterday the new version of klipper which pushes me to update MCU boot and after successful print i am getting So when I go to home all basically x and y work just fine (using eb42 v1. Just plug your probe into the Z endstop connector Manta M8P with HermitCrap V1 was working fine with microprobe V1. Another user suggests checking the wiring and connectors, and the original For each of the endstop s, rerun the QUERY_ENDSTOPS command while manually triggering the endstop. A user reports a problem with endstop x still triggered after retract when using Mainsail + Klipper on a Creality S1 Plus.
1ypcptd
okrgp9
dy2zvyc
zm8afk8
96odoa1
doxhaza
vvden
7n9tmhp
mhhobcft
ljvofg